Low Priced Bike Parts

Low Priced Bike Parts

Maillard aluminum front quick release hub laced with 36
plated spokes to a 27 inch Rigida steel wheel The chrome
plating is not perfest but it is surprisingly good $10 plus
$10 shipping

Shimano 36 spoke quick release aluminum front hub $5

Fuji gray frame fork and headset. 56 cm or 22 inch c to c
seat tube 58 cm or 23 inch top tube $20 UPS shipping is $30
http://www.geocities.com/rory60/fuji_frame_1.JPG

SR Aluminum 170mm left crankarm that fits all older Jap,
Korean and Taiwanese square tapered bottom brackets.With
retaining bolt. $7

Dia Compe center pull brake short reach. 54 to 70mm distance
from the mounting bolt to the shoe slot. complete with
cables triangular cable mount and quick release fittings to
mount on the seat post bolt $5 one only Click Below for a
picture:
http://bicycleparts.homestead.com/f...ompe_Brakes.JPG

Vetta Gel Flex mans black smooth cover saddle. It is 7
inches wide,10 inches long.Soft thick gel foam over a
flexible base.New Old Stock $5 Click below for a picture:
http://bicycleparts.homestead.com/f...dle_smaller.jpg

Brooks made in England plastic-vinyl saddle 10 1/4" by 6
1/2" unmarked $5 Click below for a picture:
http://bicycleparts.homestead.com/f...dle_smaller.jpg

SR Aluminum 26.8 seatpost with no integrated clamp $5
includes the separate steel sadddle clamp Click below for a
picture:
http://bicycleparts.homestead.com/files/Saddle_post.JPG

Steel Mtn Bike silver seat post 9 3/4 inches long with a
diameter of 7/8 of one inch 3$

Rear Deraillers

Shimano Skylark, RS and Eagle that are all short reach with
non detachable under axle bolt mounting tabs. $5 each Click
below for a picture:
http://bicycleparts.homestead.com/f..._deraillers.JPG

Fuji Maeda Ind Japan short open cage rear derailler that
comes with a removable tab to mount under the rear Axle
nuts.if you remove the tab the derailler will mount on the
tab on the frame $5

Shimano freehub spoke protectors one is for 36 spokes and 34
teeth, another is for 32 spokes and 32 teeth $2 each

Front Deraillers large offset inner plate in the cage.clamps
to a 1 1/8 seatpost,bottom pull,. Made in China $3

SR spirit that clamps to a 1 1/8 seatpost,bottom pull. It
has a reverse action so that the shift levers move the same
way to shift up or down. Poor cosmetically $3

Front Forks $10 each $6 shipping

Early model made in Chicago Schwinn.Refinished in White.The
steerer tube is 6 and 3/4" high threaded to 5 and 5/8 inches
high.The legs are thinner than most,they measure 25 mm wide
near the top but only 10 mm thick.Headset included.
http://rory60.homestead.com/files/whiteschwinnfork.jpg

Standard one inch steerer blue with scratches.The steerer is
132 mm or 5 inches high, threaded to 100 mm or 3 and 7/8
inches.There are unthreaded fender eyelets. The legs are
25.5 mm or one inch wide near the top and 18 mm or 3/4 inch
thick. there is a box crown with a chrome plated
cover.This will fit almost all small frames. Headset
included. http://rory60.homestead.com/files/bluefork.jpg

Huffy Mtn Bike one inch Forks $5 each complete with a full
headset.one for 26 inch wheels is red, the 24 inch wheel
fork is black. these require brakes that mount on a single
central hole in the crown.

Black resin Mtn Bike brake front lever with orange inner and
outer cables $3

front shfter that clamps on the handlebar with orange inner
and outer cables $3
http://members.fortunecity.com/rory...range.cable.JPG

6 speed index shifters that clamp on the handlebar with
black outer cables. A rear inner cable is included $5
http://members.fortunecity.com/rory...vers.cables.JPG

130 mm bolt on 36 spoke rear hub with 36 spokes and nipples
to lace up a 26 inch Mtn bike rim which is not included $5

SR 52 tooth aluminum chainring to fit a 120 mm 5 hole bolt
pattern originated by Stronglight for their 99 and 100
cranks and also used by SR.This bolt pattern measures 70
mm from the center of one of the 5 bolt holes to the
center of the next bolt hole.If yours measures the same it
will fit.This pattern was used for both doubles and
triples.A triple will mount 3 rings on the same bolt
pattern that permits a 28 tooth small chainring.It is
nearly new with an aluminum overide ring to keep the chain
from overshifting the big ring and also to keep your pant
cuff out of the chain. $3

Stems and Handlebars

SR aluminum Road Stem short 50 mm reach for handlebars with
a one inch or
26.4 diameter the stem diameter is the english standard .222
It is longer than usual at 19 cm Similar Nitto Youth 80
MM reach i6 cm length click below for a picture:
http://bicycleparts.homestead.com/f...short_reach.jpg

two steel 10 speed handlebars and steel stems. The chrome
plating is still good. One bar is 13"wide edge to edge
5"reach c to c and 5 1/2"drop c to c. The other is 16 1/2-5
27/2-5 3/4. Both stems have a reach of 2 1/4" and a stem
diameter of about 20mm. Either bar and stem is $15 plus
$7 shipping.
http://members.fortunecity.com/rory...peed.hdlbrs.JPG

Fuji Nitto Olympeade Steel 10 speed Handlebar 15 1/2"c to c
4 1/2" reach 6"drop. only a lttle rust $5

Steel Mtn Bike handlebars,one is flat black with a 6 degree
pullback,another is black 23"wide with a 6 degee
pullback,the last is 23"wide gray with an 8 degree pullback.
$5 each
http://members.fortunecity.com/rory....mtn.hdlbrs.JPG

Dia Compe center pull brake short reach. 54 to 70mm distance
from the mounting bolt to the shoe slot. complete with
cables triangular cable mount and quick release fittings to
mount on the seat post bolt $5 one only Click Below for a
picture:
http://bicycleparts.homestead.com/f...ompe_Brakes.JPG

priority mail is $3.50 additional on most items.Pay Pal OK.

Phone 732 566 2865 Aberdeen NJ Paypal name DonaldORourke Pay
Pal from a credit card is 2.9% plus .30 cents more
https://secure.paypal.com/affil/pal...40optonline.net