unwanted stems - any interest?

Velvet said:

As the subject says - I have three stems, all of which have been on my bike for varying lengths
of time.

One is a black ITM '7'-shaped 22.2mm quill stem, front-loading. On bike from new, done less than
100 miles, never been in rain. Possibly missing little plug for hole where the adjustment is.

Next is an adjustable-angle stem, been on the bike for very very few miles, having discovered it
was too high for existing cable slack and clamped on rear brake on sharp turns ;-) Chromed finish,
22.2mm quill, adjusts between -10 deg (points slightly to ground) and +60 deg rake (pointing up in
air) with 0 deg being a right angle, iirc. 'Pro' zoom seems to be the make. Front loading. Also
never been in rain.

And last, a second?hand quill to ahead adapter stem. 22.2mm quill base, with a shim to convert to
what I *think* is the larger of the ahead sizes (not the 25.4, which is what the bare ahead part
of it seems to be). It's a little rusty around the part that the shim fits over, and requires a
long allen-key bit on a wrench to fit (the bolt is recessed quite deep inside the stem).

Can provide more details if needed, or a pic. Given the first two are as new, looking for
something not too far off retail for them, but the third probably not more than a few quid (plus
postage for all of them, naturally).

Velvet

How long is the ITM quill?

--

-Alex

----------------------------------
[email hidden]

alexpg.ath.cxcycling.phpOpen ↗ westerleycycling.org.ukwesterleycycling.org.ukOpen ↗
----------------------------------

Alex Graham said:

Velvet said:

As the subject says - I have three stems, all of which have been on my bike for varying lengths
of time.

One is a black ITM '7'-shaped 22.2mm quill stem, front-loading. On bike from new, done less than
100 miles, never been in rain. Possibly missing little plug for hole where the adjustment is.

Next is an adjustable-angle stem, been on the bike for very very few miles, having discovered it
was too high for existing cable slack and clamped on rear brake on sharp turns ;-) Chromed
finish, 22.2mm quill, adjusts between -10 deg (points slightly to ground) and +60 deg rake
(pointing up in air) with 0 deg being a right angle, iirc. 'Pro' zoom seems to be the make. Front
loading. Also never been in rain.

And last, a second?hand quill to ahead adapter stem. 22.2mm quill base, with a shim to convert to
what I *think* is the larger of the ahead sizes (not the 25.4, which is what the bare ahead part
of it seems to be). It's a little rusty around the part that the shim fits over, and requires a
long allen-key bit on a wrench to fit (the bolt is recessed quite deep inside the stem).

Can provide more details if needed, or a pic. Given the first two are as new, looking for
something not too far off retail for them, but the third probably not more than a few quid (plus
postage for all of them, naturally).

Velvet

How long is the ITM quill?

Not quite sure how to measure, but it's 85mm from min insertion line to top of stem, then 100mm from
back of stem to middle of clamp round bars? If measured from middle of adjusting bolt hole in top of
stem to middle of clamp around bars, 90mm. Like I said, it's a 7 shape, so has that slant to the
stem that puts the other bit on roughly horizontal - couldn't tell you if it's actually a slight
downhill angle as it's not been on the bike for quite a while.

Having said it's an ITM - I think that's what the Dawes website says - there's no really much in the
way of manufacturer ID on the stem itself. Came off Dawes Audax bike, bought in autumn 2001, iirc.

Velvet

Velvet <[email hidden]> wrote

Quoted message said:

Not quite sure how to measure, but it's 85mm from min insertion line to top of stem, then 100mm
from back of stem to middle of clamp round bars? If measured from middle of adjusting bolt hole in
top of stem to middle of clamp around bars, 90mm. Like I said, it's a 7 shape, so has that slant
to the stem that puts the other bit on roughly horizontal - couldn't tell you if it's actually a
slight downhill angle as it's not been on the bike for quite a while.

It's a 90mm stem.

The height range (min insertion line to bottom of horizontal bit) is very rarely quoted, unless
that's the point of that model of stem (ie more than 2 or 3 inches).

Andrew

Andrew Sweetman said:

Velvet <[email hidden]> wrote

Quoted message said:

Not quite sure how to measure, but it's 85mm from min insertion line to top of stem, then 100mm
from back of stem to middle of clamp round bars? If measured from middle of adjusting bolt hole in
top of stem to middle of clamp around bars, 90mm. Like I said, it's a 7 shape, so has that slant
to the stem that puts the other bit on roughly horizontal - couldn't tell you if it's actually a
slight downhill angle as it's not been on the bike for quite a while.

It's a 90mm stem.

The height range (min insertion line to bottom of horizontal bit) is very rarely quoted, unless
that's the point of that model of stem (ie more than 2 or 3 inches).

Andrew

Yeah, but for someone looking for a stem to be shorter/taller than the 'norm' it's a very important
(and always lacking) measurement, IME.

Velvet