42mm Bearing clamp fabrication?

chrome said:

I'm wondering if anyone has fabricated their own bearing clamps for a
home made uni frame? I've seen 40mm United clamps at UDC, but I'm
looking for 42mm to hold a Moment hub. Something pre machined would
work also, as I can braze them onto the frame....

Cr

I know for a fact, and experience, that the Moment bearings fit into
the standard 40mm holders. No problems at all - just use the Uniteds.
🙂

--
UniTyler
------------------------------------------------------------------------
UniTyler's Profile: http://www.unicyclist.com/profile/6120
View this thread: http://www.unicyclist.com/thread/58623

Cool! Which frame is your Moment hub in?

--
chrome
------------------------------------------------------------------------
chrome's Profile: http://www.unicyclist.com/profile/12885
View this thread: http://www.unicyclist.com/thread/58623

chrome said:

I'm wondering if anyone has fabricated their own bearing clamps for a
home made uni frame? I've seen 40mm United clamps at UDC, but I'm
looking for 42mm to hold a Moment hub. Something pre machined would
work also, as I can braze them onto the frame....

Cr

I have fabricated some... not an easy way to go. plus mine give me
trouble some times because it doesn't fit perfectly
if you are building a frame I would advise buying some main caps off
udc. it is the easiest way to go about abtaining some

--
torkerdx

gordito8me said:

it's like running across the highway at rush hour. Dangerous, stupid,
but not really that fun.

Unicaw89 said:

Koxx rapes Torker hard!

unifreak7 said:

Where they should be - Holding your unicycle, ready to quit kissing and
get out and practice.

------------------------------------------------------------------------
torkerdx's Profile: http://www.unicyclist.com/profile/12543
View this thread: http://www.unicyclist.com/thread/58623

It seems that people have had most sucess machining bearing collars to
the size they need to make thier own bearing holders. But I ran 42mm
bearings (03 KH hub) in a 40mm frame (nimbus II extra-wide) for years
no problems.

--
kington99

Dave

- what a thoroughly post-modern subversion of the cycling genre -
------------------------------------------------------------------------
kington99's Profile: http://www.unicyclist.com/profile/9417
View this thread: http://www.unicyclist.com/thread/58623

chrome said:

Cool! Which frame is your Moment hub in?

My Moment hub is in a Yuni 24" frame set up with a DX32 rim, 165mm KH
cranks, and a Duro Leopard 3" tire.

+-------------------------------------------------------------------+
|Filename: mini-DSCF5668.JPG |
|Download: http://www.unicyclist.com/attachment/18435 |
+-------------------------------------------------------------------+

--
UniTyler
------------------------------------------------------------------------
UniTyler's Profile: http://www.unicyclist.com/profile/6120
View this thread: http://www.unicyclist.com/thread/58623

I appreciate the information.

A friend of mine has built like 15 or 20 MTBs. He's encouraging me to
build my own uni frame. I'll learn how to spoke and true my wheel. It
will be an opportunity to learn something new. I've had a good
industrial education, and he has a garage full of machine tools. I can
weld and machine the components.

Should the bearing holders have a circumferential flange on each side
of the bearing? The bearing holders in Jack Wiley's book are made from
tubing, without a flange on the inside or outside. There is probably a
strength advantage in capturing both sides the outer bearing race?

Cr

--
chrome
------------------------------------------------------------------------
chrome's Profile: http://www.unicyclist.com/profile/12885
View this thread: http://www.unicyclist.com/thread/58623

Without a flange on atleast one side you're relying on the friction to
hold the wheel central, this may well not be enough as you can't
tighten down on the bearings very tightly. Ideally you'd like a flange
on both sides, if you only put them on the outside then the frame can
still splay outwards. You can achieve this effect by welding a plate
over the end of a machine collar, it doesn't necessarily require
machine work.

--
kington99

Dave

- what a thoroughly post-modern subversion of the cycling genre -
------------------------------------------------------------------------
kington99's Profile: http://www.unicyclist.com/profile/9417
View this thread: http://www.unicyclist.com/thread/58623

Check out this thread;

http://tinyurl.com/38zu9k

We have made both 40 and 42mm holders, and about 5 frames total. And we
just happen to have some bearing holders for sale. PM me if you are
interested.

--
Jim_Rob

TTFN- JR

The Sage claims nothing, and so cannot be reproached, Lao Tzu
------------------------------------------------------------------------
Jim_Rob's Profile: http://www.unicyclist.com/profile/3824
View this thread: http://www.unicyclist.com/thread/58623

if you want plans for the kh ones i can give them to you

[image:
http://i80.photobucket.com/albums/j166/unicyclepa/umm/Picture1.jpg]

--
unicyclepa

www.unicyclepa.com
we suck
but its all good
team YAMS member in your sig or title and say
------------------------------------------------------------------------
unicyclepa's Profile: http://www.unicyclist.com/profile/9246
View this thread: http://www.unicyclist.com/thread/58623