so how tight are you getting those bolts?

ant said:

I got my first set of aero bars, and slapped them onto my bars this afternoon. The bolts came
pre-prepped with loctite, I screwed them down hard, and then tried to move the aero bars. With not
much effort, I could move them up and down. This worried me a lot, so I pulled the bolts out,
greased them, and cranked them down hard. Then, when I tried again, with a strong shove, the
aerobars/handlebar rotate within the stem clamp (a coda threaded with a 2-bolt faceplate, i assume
aluminum). It does take a good bit of force to do this, but the fact remains that I can do it.
From on the bike, I can not push the bars down, but with effort can pull them up, rotating the
entire bar assembly within the clamp. I know I greased those stem bolts when I put the bars in a
month ago, and I've tightened them as much as I can with my 6" allen wrench and a good bit of
muscling. I'm at the point where im worried abotu stripping either the bolt threads or the allen
hole in the bolt. The allen key has already slipped out once under pressure.

What gives? Are aerobars always going to move if you try? If i push down on them really hard, the
bar assembly stays in place and the rear wheel lifts. But if i pull up on them with weight in the
saddle, I rotate the bar assembly up, and I dont want to think about that happening every time I
want to sprint.

what should I do?

This is a poor application for Loctite. The bolt heads and the undersides of the heads should be
greased. This will result in a greater tightening force for a given amount of torque, and reduce the
risk of stripping the threads.

Some handlebars, especailly heat treated ones, are slipperier than others.

A reliable fix is to sandwich a little piece of sandpaper inside the clamp area for better traction.

Sheldon "You Do NOT Want These To Slip!" Brown +-----------------------------------------+
| A ship in the harbor is safe, but | that is not what ships are built for. | --John A. Shedd |
+-----------------------------------------+ Harris Cyclery, West Newton, Massachusetts Phone
617-244-9772 FAX 617-244-1041 harriscyclery.comharriscyclery.comOpen ↗ Hard-to-find parts shipped Worldwide
captainbike.comcaptainbike.comOpen ↗ sheldonbrown.comsheldonbrown.comOpen ↗

Hey Anthony. My solution would be to thoroughly clean all surfaces (inside of stem and clamping
surface of handlebar) to remove all grease/oil and oxidation.... then (if either of the surfaces are
smooth to the touch, such as painted or "clear anodised"😉 sand the areas with really fine sandpaper
or steel wool. You don't want to remove material, or reduce the clamping area by knurling the
areas... just take the shine off like you would when scuffing a paintjob to apply another coat. My
easton EA-70 bars were extremely slippy until I did this (and even then I had to quit using my
favorite Titec Ti 1" quilled stem as the clamp still would not tighten firmly enough). Sheldon's
advice works good too... I used a similar technique on quite a few bars at the ITU event in Edmonton
last year when we did the tech inspections..... nothing ruins a triathelete's weekend like having to
remove his aero bars because they did not meet inspection or they stripped threads trying to get
them to stay put. Good luck and let us know how it turned out. Keith.

"The knack lies in learning to throw yourself
- at the ground and miss" Douglas Adams.

"ant" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

I got my first set of aero bars, and slapped them onto my bars this afternoon. The bolts came
pre-prepped with loctite, I screwed them down hard, and then tried to move the aero bars. With not
much effort, I could move them up and down. This worried me a lot, so I pulled the bolts out,
greased them, and cranked them down hard. Then, when I tried again, with a strong shove, the
aerobars/handlebar rotate within the stem clamp (a coda threaded with a 2-bolt faceplate, i assume
aluminum). It does take a good bit of force to do this, but the fact remains that I can do it.
From on the bike, I can not push the bars down, but with effort can pull them up, rotating the
entire bar assembly within the clamp. I know I greased those stem bolts when I put the bars in a
month ago, and I've tightened them as much as I can with my 6" allen wrench and a good bit of
muscling. I'm at the point where im worried abotu stripping either the bolt threads or the allen
hole in the bolt. The allen key has already slipped out once under pressure.

What gives? Are aerobars always going to move if you try? If i push down on them really hard, the
bar assembly stays in place and the rear wheel lifts. But if i pull up on them with weight in the
saddle, I rotate the bar assembly up, and I dont want to think about that happening every time I
want to sprint.

what should I do?

"ant" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

I got my first set of aero bars, and slapped them onto my bars this

What gives? Are aerobars always going to move if you try?

Quoted message said:

I dont want to think about that happening every time I want to sprint.

what should I do?

Don't sprint on the bars. Seriously, you don't want to push or pull heavily on the ends of the
aerobars, they're not designed for that. Your weight should be balanced so that there is little or
no torque on the aerobars.

Idid neither of those things. When I hit the pothole on a slight downgrade, the ambulance took me to
the hospital for a broken hip, left wrist and thumb. I haven't had the nerve to use the bars since.

Peter Cole said:

Don't sprint on the bars. Seriously, you don't want to push or pull heavily on the ends of the
aerobars, they're not designed for that. Your weight should be balanced so that there is little or
no torque on the aerobars.

Sheldon Brown <[email hidden]> wrote in message
news:<[email hidden]>...

Quoted message said:

ant said:

Are aerobars always going to move if you try? If i push down on them really hard, the bar
assembly stays in place and the rear wheel lifts. But if i pull up on them with weight in the
saddle, I rotate the bar assembly up, and I dont want to think about that happening every time I
want to sprint.

what should I do?

Sheldon replied:

Quoted message said:

This is a poor application for Loctite. The bolt heads and the undersides of the heads should be
greased. This will result in a greater tightening force for a given amount of torque, and reduce
the risk of stripping the threads.

Some handlebars, especailly heat treated ones, are slipperier than others.

A reliable fix is to sandwich a little piece of sandpaper inside the clamp area for better
traction.

Thanks for the replies.

Sandpaper? shoudl the texture face in or out or it doesnt matter? The bar is scored with those
little lines, so im guessing the stem is the slippery part of this equation, ill try roughing it up
a little first, as the second poster suggested.

And good call on the loctite. I feel the same way, thats why i pulled the bolts and greased after my
initial try.

Thanks.

Hello all,

So I'm doing some training that requires me to climb some hills at 3%, 5% and 7%. O.K., so we all
know how to calculate the grade of a hill IF we know the elevation gain and the distance. Since I do
not know the elevation gains of my local hills, I was wondering if anyone has a better method of
finding out what the percent grade is of any hill?

I have heard that race officials get a topo map and calculate each hill, is there a better way? It
would be great if there was a county map that shows the percent grade of each street; is there
such a map?

Thanks for the help, Michael

"Paul Kopit" <[email hidden]> wrote in message > On Fri, 07 Mar 2003
14:58:52 GMT, "Peter Cole"

Quoted message said:

Quoted message said:

Don't sprint on the bars. Seriously, you don't want to push or pull heavily

on

Quoted message said:

Quoted message said:

the ends of the aerobars, they're not designed for that. Your weight should

be

Quoted message said:

Quoted message said:

balanced so that there is little or no torque on the aerobars.

Quoted message said:

Idid neither of those things. When I hit the pothole on a slight downgrade, the ambulance took
me to the hospital for a broken hip, left wrist and thumb. I haven't had the nerve to use the
bars since.

So, what happened to cause the crash? Did the bars rotate? Did you lose balance and control? Did
your wheel get shmushed? Was the pothole concealed under a puddle?

I pretty much ride aerobars any place I'd ride no-handed, it's only a bit more controllable
than that.

Michael James Anderson said:

I have heard that race officials get a topo map and calculate each hill, is there a better way? It
would be great if there was a county map that shows the percent grade of each street; is there
such a map?

Whny not measure them yourself? See how this inventive person did just that:

graphics.stanford.edubike grade.htmlOpen ↗
--
terry morse Palo Alto, CA terrymorse.combikeOpen ↗

Michael James Anderson said:

So I'm doing some training that requires me to climb some hills at 3%, 5% and 7%. O.K., so we all
know how to calculate the grade of a hill IF we know the elevation gain and the distance. Since I
do not know the elevation gains of my local hills, I was wondering if anyone has a better method
of finding out what the percent grade is of any hill?

You could use a Specialized "Speed Zone Pro" altimeter that gives the gradient as well as other
altitude functions.

A less high-tech method is to measure it directly using a meter stick, a level and a mm rule to
measure the vertical distance to the road from the end of the level meter stick whose other end is
resting on the road. This is highly accurate if you pick a representative piece of road, mm being
0.1 percent.

Quoted message said:

I have heard that race officials get a topo map and calculate each hill, is there a better way? It
would be great if there was a county map that shows the percent grade of each street; is there
such a map?

That no good. There isn't enough resolution to do that and roads generally do not cross contour
lines at right angles, so interpolation gets in the way as well.

Jobst Brandt [email hidden] Palo Alto CA

Quoted message said:

Michael James Anderson said:

I have heard that race officials get a topo map and calculate each hill, is there a better way?
It would be great if there was a county map that shows the percent grade of each street; is there
such a map?

That no good. There isn't enough resolution to do that and roads generally do not cross contour
lines at right angles, so interpolation gets in the way as well.

Unless the road is tilted side-to-side it has to cross the contours at a right angle. You just have
to look closely to see how the contour bends to meet the road. As to resolution, most topo maps in
my experience show contours every 10 feet, so the resolution would be +/- 10 feet or so, depending
on how well you can interpolate. Whether that's good enough depends on how high the hill is and how
precisely you need to know the grade. For a 7% grade on a 1:24,000 map, the contours are 0.07"
apart, which should allow interpolation to half a contour at each end. If the hill is 100 feet high,
that would be +/- 10%.
--
Ray Heindl (remove the X to reply)

Ray Heindl said:

Quoted message said:

Quoted message said:

I have heard that race officials get a topo map and calculate each hill, is there a better way?
It would be great if there was a county map that shows the percent grade of each street; is
there such a map?

Quoted message said:

Quoted message said:

That no good. There isn't enough resolution to do that and roads generally do not cross contour
lines at right angles, so interpolation gets in the way as well.

Quoted message said:

Unless the road is tilted side-to-side it has to cross the contours at a right angle. You just
have to look closely to see how the contour bends to meet the road. As to resolution, most topo
maps in my experience show contours every 10 feet, so the resolution would be +/- 10 feet or so,
depending on how well you can interpolate. Whether that's good enough depends on how high the hill
is and how precisely you need to know the grade. For a 7% grade on a 1:24,000 map, the contours
are 0.07" apart, which should allow interpolation to half a contour at each end. If the hill is
100 feet high, that would be +/- 10%.

I think you are imagining a resolution and map design that doesn't occur. Contour lines are not made
to include road benches but rather the natural contour of the terrain, just as they don't go up
sloping lines of building roofs. I think a typical map such as the following are a good example.

topozone.commap.aspOpen ↗

Jobst Brandt [email hidden] Palo Alto CA

(ant) said:

I got my first set of aero bars, and slapped them onto my bars this afternoon. The bolts came
pre-prepped with loctite, I screwed them down hard, and then tried to move the aero bars. With not
much effort, I could move them up and down. This worried me a lot, so I pulled the bolts out,
greased them, and cranked them down hard. Then, when I tried again, with a strong shove, the
aerobars/handlebar rotate within the stem clamp (a coda threaded with a 2-bolt faceplate, i assume
aluminum). It does take a good bit of force to do this, but the fact remains that I can do it. From
on the bike, I can not push the bars down, but with effort can pull them up, rotating the entire
bar assembly within the clamp. I know I greased those stem bolts when I put the bars in a month
ago, and I've tightened them as much as I can with my 6" allen wrench and a good bit of muscling.
I'm at the point where im worried abotu stripping either the bolt threads or the allen hole in the
bolt. The allen key has already slipped out once under pressure.

What gives? Are aerobars always going to move if you try? If i push down on them really hard, the
bar assembly stays in place and the rear wheel lifts. But if i pull up on them with weight in the
saddle, I rotate the bar assembly up, and I dont want to think about that happening every time I
want to sprint.

what should I do?

Maybe a good 4-bolt stem would be a good place to start, though another way to get your current
set-up to stay put might be black loctite (the one for permanent fixing, sometimes labelled for
studs and bearings). Bottom line is the stem clamp is not designed to take the large amounts of
torque which aero bars apply. Normal drop bars, straightish flat bars or even moustache bars have
the push/pull force axis running almost directly through the bar/stem clamp axis, and this is the
set-up for which the clamp was designed all those years ago. Having said all that, I never had a
problem with my off axis forces using a Cinelli 62 cowhorn bar, Profile Aero 2 and Cinelli Grammo
stem, without resorting to any special treatment. On the other hand, even top continental pros have
occasionally suffered aero bar rotation problems. This might be one of those cases, like slipping
seat posts, where the best solution is to have the clamp made of much harder material than the thing
being clamped.

Kinky Cowboy

*Your milage may vary Batteries not included May contain traces of nuts.

Paul Kopit <[email hidden]> wrote in message
news:<[email hidden]>...

Quoted message said:

Idid neither of those things. When I hit the pothole on a slight downgrade, the ambulance took
me to the hospital for a broken hip, left wrist and thumb. I haven't had the nerve to use the
bars since.

i did not hear that. i did not hear that. i did not...

Michael James Anderson said:

Hello all,

So I'm doing some training that requires me to climb some hills at 3%, 5% and 7%. O.K., so we all
know how to calculate the grade of a hill IF we know the elevation gain and the distance. Since I
do not know the elevation gains of my local hills, I was wondering if anyone has a better method
of finding out what the percent grade is of any hill?

Take a yardstick and a level, or better yet a long level. I have one that is 4 feet. Put one end on
the road, hold it level, and measure down to the road with another yardstick. The ratio of these
measurements is the % grade (the tangent of the angle of the road).

--

David L. Johnson

__o | "Business!" cried the Ghost. "Mankind was my business. The _`\(,_ | common welfare was my
business; charity, mercy, forbearance, (_)/ (_) | and benevolence, were, all, my business. The
dealings of my trade were but a drop of water in the comprehensive ocean of my business!"
--Dickens, "A Christmas Carol"

In article <[email hidden]>, [email hidden]

(ant) said:

I got my first set of aero bars, and slapped them onto my bars this afternoon. The bolts came
pre-prepped with loctite, I screwed them down hard, and then tried to move the aero bars. With not
much effort, I could move them up and down.

Perhaps the aero bar to handle bar interface would be a better place for the loctite, rather than
the bolt threads.

Tom Gibb <[email hidden]

Peter Cole said:

So, what happened to cause the crash? Did the bars rotate? Did you lose balance and control? Did
your wheel get shmushed? Was the pothole concealed under a puddle?

I pretty much ride aerobars any place I'd ride no-handed, it's only a bit more controllable
than that.

I hit the depression and the handlebars rotated forward. I literally got slammed to the ground. The
bicycle sustained little damage as I took all the impact. The bars are TTT Prima and the stem is ITM
Ecylpse. Were I to use a clipon again, I'd use beefier bars, no grease, sandpaper, and whatever else
I could to stop anything from moving. I can't ride without hands but can do a track stand.

In article <[email hidden]>, "David L. Johnson" <David L. Johnson

Quoted message said:

Michael James Anderson said:

So I'm doing some training that requires me to climb some hills at 3%, 5% and 7%. O.K., so we
all know how to calculate the grade of a hill IF we know the elevation gain and the distance.
Since I do not know the elevation gains of my local hills, I was wondering if anyone has a
better method of finding out what the percent grade is of any hill?

Take a yardstick and a level, or better yet a long level. I have one that is 4 feet. Put one end
on the road, hold it level, and measure down to the road with another yardstick. The ratio of
these measurements is the % grade (the tangent of the angle of the road).

Yah, but good heavens is it necessary to be so literal about hill training? Look for a mild, a
moderate and a steepish hill in your neighborhood and that will be close enough. I know Joe Friel
prescribes this stuff but IMHO at least it's just not a significant difference if the hill is
2.75% or 3.25%.

Quoted message said:

Quoted message said:

Unless the road is tilted side-to-side it has to cross the contours at a right angle. You just
have to look closely to see how the contour bends to meet the road. As to resolution, most topo
maps in my experience show contours every 10 feet, so the resolution would be +/- 10 feet or so,
depending on how well you can interpolate. Whether that's good enough depends on how high the
hill is and how precisely you need to know the grade. For a 7% grade on a 1:24,000 map, the
contours are 0.07" apart, which should allow interpolation to half a contour at each end. If the
hill is 100 feet high, that would be +/- 10%.

I think you are imagining a resolution and map design that doesn't occur. Contour lines are not
made to include road benches but rather the natural contour of the terrain, just as they don't go
up sloping lines of building roofs. I think a typical map such as the following are a good
example.

topozone.commap.aspOpen ↗

Don't try this link if you use Opera; it starts an infinite series of error messages.

I wouldn't call that a "typical" topo map; it's way too small a scale to try to measure anything off
of. I imagine the original poster was referring to real, large-scale topo maps. Print your example
at 1.5 x 2 feet, like a USGS paper map, and you might be able to measure from
it.

On the USGS 7.5-minute topo map I'm looking at right now, every contour I checked that crosses a
road is perpendicular to it, as near as dammit. Many of the contour lines have little rectangular
jogs, showing where hills were cut out to put the roads through.

Here's a small part of the map: <http://members.nccw.net/rheindl/topo1.jpg> This represents a piece
of the map about 1.5 inches wide, or about 3000 feet on the ground. In the middle of the picture,
Washington Blvd has a grade of 1.8% as measured by a dial caliper. What's so difficult about that?

--
Ray Heindl (remove the X to reply)

That would work. Just make sure the bars are positioned where you want them. "TBGibb"
<[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

In article <[email hidden]>, [email hidden]

(ant) said:

I got my first set of aero bars, and slapped them onto my bars this afternoon. The bolts came
pre-prepped with loctite, I screwed them down hard, and then tried to move the aero bars. With
not much effort, I could move them up and down.

Perhaps the aero bar to handle bar interface would be a better place for

the

Quoted message said:

loctite, rather than the bolt threads.

Tom Gibb <[email hidden]