Thought of this on holidays. I had problems with a front derailleur and could not get enough tension on it to get it to work properly, even using barrel adjuster, as I did not have a big pliers.
I thought and thought and then...
I removed the cable stop where the left downtube changer used to be in older bikes, adjust the cable and then pulled the stop back into position and fixed it. I was then able to slowly let the cable out by trial and error until I got the changer right.
A good trick. I've never seen anyone do it, although some must have thought of it years ago.
Thought of this on holidays. I had problems with a front derailleur and could not get enough tension on it to get it to work properly, even using barrel adjuster, as I did not have a big pliers.
Just grab the wire with a pair of pliers. pull it tight and tighten the clamp. Cable tension isn't a big deal on FDs. Phil Brown
"Gearóid Ó Laoi/Garry Lee" <[email hidden]> wrote in message news:<[email hidden]>...
Quoted message said:
Thought of this on holidays. I had problems with a front derailleur and could not get enough tension on it to get it to work properly, even using barrel adjuster, as I did not have a big pliers.
I thought and thought and then...
I removed the cable stop where the left downtube changer used to be in older bikes, adjust the cable and then pulled the stop back into position and fixed it. I was then able to slowly let the cable out by trial and error until I got the changer right.
A good trick. I've never seen anyone do it, although some must have thought of it years ago.
Hi, it would it be helpful to know what kind of derailleur and shifter you are using. In my limited experience with Shimano, if you put the chain on the smallest chainring and set the shifter to that same position, you should be able to pull the cable plenty tight by hand. Be sure to have the barrel adjuster turned all the way in. With indexed shifters, if the cable is too tight it won't trim properly. I certainly didn't need any pliers, to do this.
The problem was that I did NOT have a pliers and that I had a recently fitted cable with almost no spare to get a good grip on it to pull it tight enough. If I were fitting a new cable and had a cable cutter it would have been a different kettle of fish. I could not get it tight enough for it to shift the chain onto the big ring, without the trick I've just mentioned. Some of you will need this some day, so just remember it.
The problem was that I did NOT have a pliers and that I had a recently fitted cable with almost no spare to get a good grip on it to pull it tight enough. If I were fitting a new cable and had a cable cutter it would have been a different kettle of fish. I could not get it tight enough for it to shift the chain onto the big ring, without the trick I've just mentioned. Some of you will need this some day, so just remember it.
Lighten up, Garry. You weren't presenting your method as a field expedient. t's OK for that. Phil Brown
Lighten up, Garry. You weren't presenting your method as a field
expedient.
Quoted message said:
t's OK for that.
Well I was, as I said that I was on holidays and had no big pliers... it's a clever trick, even though I say so myself.
I'll give you another trick I had to invent some years ago. Out the country one evening, miles from home, puncture. Found that pump rubber had worn such that it did not make a seal with the valve and I cound not pump the tyre.
Took me a while to think of this and try it. I wrapped a leaf around the valve and then pushed on the pump. Problem solved.
Without pliers? shift the chain onto the large ring and WITHOUT pedaling, drop the shifter to the small ring. Then just slightly tension the cable and tighten the clamp. Cable should be close to perfect, requiring only little adjustment at the barrel.
If barrel adjusters are difficult in the field, this can also be done while coasting. Just drop a cog or two WITHOUT pedaling and the cable will slacken, allowing adjustments to be made easier.
"Gearóid Ó Laoi/Garry Lee" <[email hidden]> wrote in message news:<[email hidden]>...
Quoted message said:
Quoted message said:
Lighten up, Garry. You weren't presenting your method as a field
expedient.
Quoted message said:
t's OK for that.
Well I was, as I said that I was on holidays and had no big pliers... it's a clever trick, even though I say so myself.
I'll give you another trick I had to invent some years ago. Out the country one evening, miles from home, puncture. Found that pump rubber had worn such that it did not make a seal with the valve and I cound not pump the tyre.
Took me a while to think of this and try it. I wrapped a leaf around the valve and then pushed on the pump. Problem solved.
You are a regular McGuyver!
You never did identify the problem derailleur and shifter, what is it?
It's a compact mountain bike Shimano front shifter. Bottom pull, band on. Not sure which spec, but good quality, maybe ultegra or such, to judge from nuts etc. It's one of those annoying design where the pinch nut disappears unless in small chainring zone. You have to take off the rear wheel to mess with it, unless you have a long allen key.
