fh-7800 hub dimensions

"Eric" <[email hidden]> wrote in message news:<[email hidden]>...

Quoted message said:

I want to built up one of these hubs and would like the dimensions to enter
into a spoke calculator. I use the spocalc.exe.
I need center to each flange distance and flange diameter.
Thanks
Eric

Hi, the specs are on this website:
http://www.dura-ace.com/publish/content/duraace/en/home/the_product0/wheels.html

Life is Good!
Jeff

<< Hi, the specs are on this website:
http://www.dura-ace.com/publish/content/duraace/en/home/the_product0/wheel
s.html

Quoted message said:

Quoted message said:

<BR><BR>

Doesn't gibe flange diameter or center to flange...tho-I think the same as 7700
hubs tho-

REMEMBER-10s cogsets only!!

Peter Chisholm
Vecchio's Bicicletteria
1833 Pearl St.
Boulder, CO, 80302
(303)440-3535
http://www.vecchios.com
"Ruote convenzionali costruite eccezionalmente bene"

Jeff Starr said:

"Eric" <[email hidden]> wrote in message
news:<[email hidden]>...

Quoted message said:

I want to built up one of these hubs and would like the dimensions to
enter into a spoke calculator. I use the spocalc.exe. I need center to
each flange distance and flange diameter. Thanks Eric

Hi, the specs are on this website: http://www.dura-/http://www.dura- ace.com/publish/content/duraace/en/home/the_product0/w-
heels.html
Life is Good! Jeff

Life may be good, but the URL you gave isn't. Hole PCD 44mm Flange
Distance 56.9 Dish 7.9 From: http://tinyurl.com/yqzem or if you can cut
and paste the original too long URL: http://www.dura-
ace.com/publish/content/duraace/en/home/the_
product0/wheels.ExtraMainContentPar.0007.File.tmp/FH7800_spe
c.pdf I agree with Peter Chisholm. The flanges are larger, spacing
slightly different, spoke hole diameter is identical. When I look at
the current version that Sheldon Brown carries on his web site I see
the FH-7800 hub with correct dimensions listed. If you saved an older
version you should revisit the site and get the new chart.

--

[email hidden] (Qui si parla Campagnolo ) wrote in message news:<[email hidden]>...

Quoted message said:

<< Hi, the specs are on this website:
http://www.dura-ace.com/publish/content/duraace/en/home/the_product0/wheel
s.html

Quoted message said:

Quoted message said:

<BR><BR>

Doesn't gibe flange diameter or center to flange...tho-I think the same as 7700
hubs tho-

REMEMBER-10s cogsets only!!

Peter Chisholm
Vecchio's Bicicletteria
1833 Pearl St.
Boulder, CO, 80302
(303)440-3535
http://www.vecchios.com
"Ruote convenzionali costruite eccezionalmente bene"

Peter, did you try clicking on pdf files at bottom of page, where it
has the links - FH-7800 Specifications and HB-7800 Specifications?
The info might be in there.
I ordered the back hub [DA FH-7700] for the wheels I am going to have
built. It looks like June, for enough funds to have you do the work.
I'll be in touch.

Life is Good!
Jeff

[email hidden] (Qui si parla Campagnolo ) wrote in message news:<[email hidden]>...

Quoted message said:

<< Hi, the specs are on this website:
http://www.dura-ace.com/publish/content/duraace/en/home/the_product0/wheel
s.html

Quoted message said:

Quoted message said:

<BR><BR>

Doesn't gibe flange diameter or center to flange...tho-I think the same as 7700
hubs tho-

REMEMBER-10s cogsets only!!

http://www.dura-ace.com/publish/content/duraace/en/home/the_product0/wheels.ExtraMainContentPar.0007.File.tmp/FH7800_spec.pdf

shows that flange diameter is 44mm. Distance to right flange is 49mm.
Distance to left flange is 64.8mm.

I'd be willing to bet that these figures are within a couple tenths of
a millimeter of the FH-7700 hub.

Jeff