Is the chain skipping or what?

"Pat" <[email hidden]> wrote in message "]news:[email hidden]...

Quoted message said:

Hello. I have a problem with my mountainbike that's been pretty common

with

Quoted message said:

bikes I've had but now find it really irritating and want to fix it.

When I put a lot of pressure on the pedal (like when I start pedaling from rest), the pedal
jerkily advances a little bit without the wheels moving

and

Quoted message said:

then it "catches" and the wheels turn as the pedal turns. It almost feels like every link on the
chain is skipping one cog but that seems impossible for every cog would have to be worn.

When it happens, it's a jolt to the body which once in a while almost

knocks

Quoted message said:

me off the bike.

The bike is not knew so I think it's due to worn parts but I can't figure out what exact parts are
causing it. Any help would be appreciated.

Thanks.

Check the cassette - the group of cogs on the rear wheel - for excess wear. If the spaces between
teeth on the cassette are shallower than half-circles, you need a new one of them. Very, very
careful adjustment of the rear derailleur can help to alleviate the skipping, but that is just
prolonging the inevitable. If your chain is new and the cassette is not the skiping will be very
noticable.

FWIW, I get less than a thousand (mostly dirt) miles out of cassettes...do you know how much riding
was done on yours?

If you replace the cassette and chain, and double-check your rear mech setup, you should have
no problems.

Of course, you could just need new chainrings up front. Or both...

Chris

Worn cogset will do it. You say "worn parts", which points in this direction. Does it skip all over
the cogset? Or just on a favorite cogwheel(s)? If the bike gets a new chain and suddenly starts
skipping, worn cogset is the magic ticket. One of my bikes always slips on the smallest two cogs and
this started the last time I changed the chain. Now if only that shiny new cogset could make it from
the bench to the bike...

Note- you may not need to change the whole cogset. I tend to get much higher wear on the smaller
wheels than the bigger ones. I presume because of higher contact forces between the chain and
cogwheel. Take your cogset out and you may see that the outer two are separate (e.g. most Shimanos)
or that even the whole set can be taken apart. My wallet says that it is always cheaper to replace
one cogwheel than an entire set.

Alternatively, it could be a maladjusted deraileur. I have this problem on a new (less than 100km)
bike. I get skipping all over the cogset and it drives me bananas. I think it is going up on the
stand before today's ride.

-Dave

Pat said:

Hello. I have a problem with my mountainbike that's been pretty common with bikes I've had but now
find it really irritating and want to fix it.

When I put a lot of pressure on the pedal (like when I start pedaling from rest), the pedal
jerkily advances a little bit without the wheels moving and then it "catches" and the wheels turn
as the pedal turns. It almost feels like every link on the chain is skipping one cog but that
seems impossible for every cog would have to be worn.

When it happens, it's a jolt to the body which once in a while almost knocks me off the bike.

The bike is not knew so I think it's due to worn parts but I can't figure out what exact parts are
causing it. Any help would be appreciated.

Thanks.

the "delay" you're feeling is due to how the rear hub works. The skip you feel is the movement of
the cassette and freehub until the mechanical conection to the main hub is made. Many better (read:
more expensive) hubs have quicker "engagement", because they have more engagement points.

If it only happens when you start pedalling (whether starting or coasting), then thats what it is.
You know those clicks the rear hub makes? Thats the mechanical "pawls" clicking by the engagement
points - they're what allow the hub to "freewheel", IE coast.

for a general idea: bikepro.comd1dd ringle pawl.jpgOpen ↗ The silver
parts are the pawls.

You can prove this to yourself by carefully wheeling the bike backwards, then RIGHT after the hub
clicks, stop, and put a little bit of pressure on the pedal. It won't move far at all before it
engages. Then try it about as far from a click as you can - you'll feel the extra movement.

Jon Bond

Jonathan Bond said:

Pat said:

Hello. I have a problem with my mountainbike that's been pretty common with bikes I've had but
now find it really irritating and want to fix it.

When I put a lot of pressure on the pedal (like when I start pedaling from rest), the pedal
jerkily advances a little bit without the wheels moving and then it "catches" and the wheels turn
as the pedal turns. It almost feels like every link on the chain is skipping one cog but that
seems impossible for every cog would have to be worn.

When it happens, it's a jolt to the body which once in a while almost knocks me off the bike.

The bike is not knew so I think it's due to worn parts but I can't figure out what exact parts
are causing it. Any help would be appreciated.

Thanks.

the "delay" you're feeling is due to how the rear hub works. The skip you feel is the movement of
the cassette and freehub until the mechanical conection to the main hub is made. Many better
(read: more expensive) hubs have quicker "engagement", because they have more engagement points.

If it only happens when you start pedalling (whether starting or coasting), then thats what it is.
You know those clicks the rear hub makes? Thats the mechanical "pawls" clicking by the engagement
points - they're what allow the hub to "freewheel", IE coast.

for a general idea: bikepro.comd1dd ringle pawl.jpgOpen ↗ The silver
parts are the pawls.

You can prove this to yourself by carefully wheeling the bike backwards, then RIGHT after the hub
clicks, stop, and put a little bit of pressure on the pedal. It won't move far at all before it
engages. Then try it about as far from a click as you can - you'll feel the extra movement.

Jon Bond

Hmm, I read your post as "the bike is new, so it's not due to wear". My bad.

Yeah, go by what the other guys say.

Jon Bond shouldn't try to be helpful during finals period.

Pat said:

Hello. I have a problem with my mountainbike that's been pretty common with bikes I've had but now
find it really irritating and want to fix it.

When I put a lot of pressure on the pedal (like when I start pedaling from rest), the pedal
jerkily advances a little bit without the wheels moving and then it "catches" and the wheels turn
as the pedal turns. It almost feels like every link on the chain is skipping one cog but that
seems impossible for every cog would have to be worn.

When it happens, it's a jolt to the body which once in a while almost knocks me off the bike.

The bike is not knew so I think it's due to worn parts but I can't figure out what exact parts are
causing it. Any help would be appreciated.

Thanks.

Chain skip is the sign of a worn cog or a chain that's worn differently from the cogs and no longer
engages all of the teeth properly (new chain, old cogs). This doesn't take long with improper chain
maintenance or even with good chain maintenance in bad conditions (lots of water and grit/mud 🙂).

It's probably a combination of the above.
- Measure pin-pin on 12 links of the chain. If it's more than 12-1/16" to 12-1/8", you probably need
a new chain (a new chain's 12" -- 1"/link). You may need to measure 6 links and 1/2 the above. If
you replace the chain on a bike that's already skipping, you'll probably need to replace the
chainrings and the cassette also. They'll be worn to the wider link spacing and skip with the new
chain because only 1 tooth will bear the load!
- Does it skip in any front chainring? If so, the probalem's probably the cassette. If only one
chain ring skips, try replacing it.
- Does it skip in any rear cassette gear? If it skips in only some of the cassette gears, it's
probably a worn cassette. Otherwise, it's worn chainrings and you need to repeat the previous step
🙂). It'll usually skip in the gears that you use the most (like the one that you start out
in 🙂). Replace the cassette.

Note that replacing one of the above may not fix the problem. It may just show you the next worn
part that needs replacing...

David

i had this only when i broke my chain and bought a new one.

"Jonathan Bond" <[email hidden]> wrote in message
"]news:[email hidden]...

Quoted message said:

Jonathan Bond said:

Pat said:

Hello. I have a problem with my mountainbike that's been pretty common with bikes I've had but
now find it really irritating and want to fix it.

When I put a lot of pressure on the pedal (like when I start pedaling from rest), the pedal
jerkily advances a little bit without the wheels moving and then it "catches" and the wheels
turn as the pedal turns. It almost feels like every link on the chain is skipping one cog but
that seems impossible for every cog would have to be worn.

When it happens, it's a jolt to the body which once in a while almost knocks me off the bike.

The bike is not knew so I think it's due to worn parts but I can't

figure

Quoted message said:

Quoted message said:

Quoted message said:

out what exact parts are causing it. Any help would be appreciated.

Thanks.

the "delay" you're feeling is due to how the rear hub works. The skip you feel is the movement
of the cassette and freehub until the mechanical conection to the main hub is made. Many better
(read: more expensive) hubs have quicker "engagement", because they have more engagement points.

If it only happens when you start pedalling (whether starting or coasting), then thats what it
is. You know those clicks the rear hub makes? Thats the mechanical "pawls" clicking by the
engagement points - they're what allow the hub to "freewheel", IE coast.

for a general idea: bikepro.comd1dd ringle pawl.jpgOpen ↗ The
silver parts are the pawls.

You can prove this to yourself by carefully wheeling the bike backwards, then RIGHT after the
hub clicks, stop, and put a little bit of pressure on the pedal. It won't move far at all before
it engages. Then try it about as far from a click as you can - you'll feel the extra movement.

Jon Bond

Hmm, I read your post as "the bike is new, so it's not due to wear". My bad.

Yeah, go by what the other guys say.

Jon Bond shouldn't try to be helpful during finals period.