koxx xtp frame

It will fit a kh hub.

--
Luke Collalto

'Videos'
(http://www.youtube.com/profile?user=TeamInsomnia)
'KHU' (http://www.krisholm.com)
'UDC Australia' (http://www.unicycle.au.com)

Stealth, is always in fashion.
------------------------------------------------------------------------
Luke Collalto's Profile: http://www.unicyclist.com/profile/14600
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

ok cool. So what does averyone think of the frame itself? its will cost
me $400 lol so if I decide to it better be good.😉

--
r-cormier
------------------------------------------------------------------------
r-cormier's Profile: http://www.unicyclist.com/profile/15026
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

Luke Collalto said:

It will fit a kh hub.

Actually I don't think it will. I am assuming it has identical or
similar bearing holders as the black domina and the domina frame will
-not- fit a kh hub.

The bearings are the same size but the flanges are a lot wider on the
KH hub and the KH bearing holders are designed so the bearing sits on
the very outside edge of the holder so there are no problems with
clearance. With the domina (and probably XTP) holders, the bearing sits
in the center of the bearing holders so the holders stick out too far
and rub against the hub flanges.

I have tried to put my domina frame on both an 07 and 05 KH hub and it
rubs both of them, the 07 is much worse though. If you have an 07 KH
you can see how close the hub flanges come to bearing holders.

--
Spencer Hochberg

www.unicycle.tv/channel/Spencer
'Bedford Unicycles' (http://BedfordUnicycles.ca)
------------------------------------------------------------------------
Spencer Hochberg's Profile: http://www.unicyclist.com/profile/12659
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

wow that sucks, anyone know for sure?

--
r-cormier
------------------------------------------------------------------------
r-cormier's Profile: http://www.unicyclist.com/profile/15026
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

Get a KH frame... the XTP is way to expensive and little heavier than
the kh

--
Smilymarco

'Municycle.com' (http://www.municycle.com)

DustinSchaap said:

tamesa is hot

------------------------------------------------------------------------
Smilymarco's Profile: http://www.unicyclist.com/profile/4110
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

Let the XTP stay where it is and waith for the Triton Sponge, this will
kick there ass for strength, look and probably weight to.

Peter M

--
Probailer2

Supported by www.municycle.com
------------------------------------------------------------------------
Probailer2's Profile: http://www.unicyclist.com/profile/11034
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

I have 2 XTP frames, one with a small crack that Joe Hodges did. I'm
happy with it, I havn't had any problems but I wouldn't pay full whack
for it.
I don't know if it fits the KH Hub.your decision.It does look nice.

Joe

--
Rodgeriego

'MySpazz' (http://www.myspace.com/uniboyjoe)

forrestunifreak said:

I pulled it out today and was messing around....

------------------------------------------------------------------------
Rodgeriego's Profile: http://www.unicyclist.com/profile/9014
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

its pretty pointless telling the guy not to get it, he asks a question
can people just stay on topic?

all i can say is I dont know. Maybe its worth emailing koxx.

--
brendan

[10:10] Amanda: can i have big [censored]?
------------------------------------------------------------------------
brendan's Profile: http://www.unicyclist.com/profile/13680
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com

Spencer Hochberg said:

Actually I don't think it will. I am assuming it has identical or
similar bearing holders as the black domina and the domina frame will
-not- fit a kh hub.

The bearings are the same size but the flanges are a lot wider on the
KH hub and the KH bearing holders are designed so the bearing sits on
the very outside edge of the holder so there are no problems with
clearance. With the domina (and probably XTP) holders, the bearing sits
in the center of the bearing holders so the holders stick out too far
and rub against the hub flanges.

I have tried to put my domina frame on both an 07 and 05 KH hub and it
rubs both of them, the 07 is much worse though. If you have an 07 KH
you can see how close the hub flanges come to bearing holders.

Wow, I had no idea. Thanks.

--
Luke Collalto

'Videos'
(http://www.youtube.com/profile?user=TeamInsomnia)
'KHU' (http://www.krisholm.com)
'UDC Australia' (http://www.unicycle.au.com)

Stealth, is always in fashion.
------------------------------------------------------------------------
Luke Collalto's Profile: http://www.unicyclist.com/profile/14600
View this thread: http://www.unicyclist.com/thread/64230

Posted Via Usenet.com Premium Usenet Newsgroup Services
----------------------------------------------------------
** SPEED ** RETENTION ** COMPLETION ** ANONYMITY **
----------------------------------------------------------
http://www.usenet.com